// Copyright 2015-2016 Espressif Systems (Shanghai) PTE LTD
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at

//     http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.

// Sketch shows how to switch between WiFi and BlueTooth or use both
// Button is attached between GPIO 0 and GND and modes are switched with each press

#include "soc/soc_caps.h"
#if !CONFIG_SOC_BT_SUPPORTED
#error "This example requires native Bluetooth support"
#endif

#include "WiFi.h"
#define STA_SSID "your-ssid"
#define STA_PASS "your-pass"
#define AP_SSID  "esp32"

enum {
  STEP_BTON,
  STEP_BTOFF,
  STEP_STA,
  STEP_AP,
  STEP_AP_STA,
  STEP_OFF,
  STEP_BT_STA,
  STEP_END
};

void onButton() {
  static uint32_t step = STEP_BTON;
  switch (step) {
    case STEP_BTON:  //BT Only
      Serial.println("** Starting BT");
      btStart();
      break;
    case STEP_BTOFF:  //All Off
      Serial.println("** Stopping BT");
      btStop();
      break;
    case STEP_STA:  //STA Only
      Serial.println("** Starting STA");
      WiFi.begin(STA_SSID, STA_PASS);
      break;
    case STEP_AP:  //AP Only
      Serial.println("** Stopping STA");
      WiFi.mode(WIFI_AP);
      Serial.println("** Starting AP");
      WiFi.softAP(AP_SSID);
      break;
    case STEP_AP_STA:  //AP+STA
      Serial.println("** Starting STA");
      WiFi.begin(STA_SSID, STA_PASS);
      break;
    case STEP_OFF:  //All Off
      Serial.println("** Stopping WiFi");
      WiFi.mode(WIFI_OFF);
      break;
    case STEP_BT_STA:  //BT+STA
      Serial.println("** Starting STA+BT");
      WiFi.begin(STA_SSID, STA_PASS);
      btStart();
      break;
    case STEP_END:  //All Off
      Serial.println("** Stopping WiFi+BT");
      WiFi.mode(WIFI_OFF);
      btStop();
      break;
    default: break;
  }
  if (step == STEP_END) {
    step = STEP_BTON;
  } else {
    step++;
  }
  //little debounce
  delay(100);
}

// WARNING: WiFiEvent is called from a separate FreeRTOS task (thread)!
void WiFiEvent(WiFiEvent_t event) {
  switch (event) {
    case ARDUINO_EVENT_WIFI_AP_START:
      Serial.println("AP Started");
      WiFi.softAPsetHostname(AP_SSID);
      break;
    case ARDUINO_EVENT_WIFI_AP_STOP: Serial.println("AP Stopped"); break;
    case ARDUINO_EVENT_WIFI_STA_START:
      Serial.println("STA Started");
      WiFi.setHostname(AP_SSID);
      break;
    case ARDUINO_EVENT_WIFI_STA_CONNECTED: Serial.println("STA Connected"); break;
    case ARDUINO_EVENT_WIFI_STA_GOT_IP6:
      Serial.print("STA IPv6: ");
      Serial.println(WiFi.linkLocalIPv6());
      break;
    case ARDUINO_EVENT_WIFI_STA_GOT_IP:
      Serial.print("STA IPv4: ");
      Serial.println(WiFi.localIP());
      break;
    case ARDUINO_EVENT_WIFI_STA_DISCONNECTED: Serial.println("STA Disconnected"); break;
    case ARDUINO_EVENT_WIFI_STA_STOP:         Serial.println("STA Stopped"); break;
    default:                                  break;
  }
}

void setup() {
  Serial.begin(115200);
  pinMode(0, INPUT_PULLUP);
  WiFi.onEvent(WiFiEvent);  // Will call WiFiEvent() from another thread.
  WiFi.enableIPv6();
  Serial.print("ESP32 SDK: ");
  Serial.println(ESP.getSdkVersion());
  Serial.println("Press the button to select the next mode");
}

void loop() {
  static uint8_t lastPinState = 1;
  uint8_t pinState = digitalRead(0);
  if (!pinState && lastPinState) {
    onButton();
  }
  lastPinState = pinState;
}